Welcome to tattoo DIY!| Sign In | Register
Home >  Tattoo Wiki >  Tattoo machines >  How to judge the quality of the homemade tattoo machines?

How to judge the quality of the homemade tattoo machines?

RSS Feed
Monday 28 April, 2014 Written by tattoodiy

Homemade tattoo machines can be made by any material, as long as its strength requirements can be recognized enough . The stand or fall of difference between the tattoo machine:
The electromagnetic coil and the stability of the shrapnel bounce, depends on the processing of the early locating and tolerance to master; In addition, fixed coil screws and check out best gaskets, so as not to shift due to vibration.
Listen to the voice sometimes mislead your judgement, judge of the machine only after loading the needle and buckle on elastic correct conclusion can be drawn from actual use. Equipment, because consider cost factor, sometimes material too thin is the reason why sounds awful, thick frame voice naturally thick!
The tattoo machines on the market price disparity between amplitude is large, that in terms of quality, will be a big difference? A: the price of the machine, is that it is that sex and market reputation; In terms of quality, if the businessman in electromagnetic iron core with hanging iron this two parts with the electromagnetism pure iron is also called the soft iron, so, the machine should be no mystery! Because the soft iron is the best material of these two parts.
how to identify whether the power of the machine is soft? A: that is very troublesome, accurate method is to use high-speed cameras, observe the machine back after the loss of magnetic needle mouth in the schedule (distance), distance is soft, small distance is hard! Is the best effect with the least amount of piercing the number will be enough pigment into the target location, at this time if regardless of technique, the problem of machine is out. Fast and hard skin lesions caused by machine on the slow and soft the skin lesions caused by the machine was low. The reason: it fast and hard machine at work in the retraction to each needle mouth stay time is short, the other reason before the shell is harder, can bounce back after the excitation-loss stroke is small, then caused the tip of the pigment dip take quantity is small, can, of course, being sent to the target location is less.. On the contrary, slow and gentle machine at work in the retraction to each needle mouth for a long time, the other reason before the shrapnel is soft, can bounce back after the excitation-loss trip also big, also is equal to the amount of pigment dip take increased the needlepoint, can be admitted to a target location is much! Even though I just did experiment 2 pieces in the practice the skin pigment saturation essentially the same practice skin cross-sections were observed under the microscope, I verified the above analysis. The experiment also include the specification of the same practice for tensile test, the result was the same .
secant machine and fog machine in performance have what characteristics? A: line machine: requirement is fast and back out of the needle is fast, so as not to hang the skin! Fog machine requirements are different, according to the habit of each tattoo artist! This, is that all the production machines can't do! In general are our people in accommodating the machine (speed, strength, flexibility, speed and flexibility, related to users under the decisiveness of the needle, strength the relationship with the user's habits.
how to debug a new machine? A: any new machine can only minor adjustments, its fundamental nature, as early as it is the factory has been qualitative!! Fine tuning. This with clearance, have a direct relationship. Shell strength.
how to determine and test out the length of the needle? Answer: according to the habit of each, and the guest's skin nature! Skin thicker than the asians, europeans in some deeper, it is also a foreign artist seven reasons for seeking to bounce space is large machine, tattoo machines in use after a period of time, contact will be wear and tear, tattoo machine power and performance will decline, and how to solve this problem? A: when not in use, loosen the damping aprons, so that we can avoid the change of the power! Then there is, if the contact will wear and then use the new notes between contact point and promptly pull back and forth a few times can.
why there are all-in-one and fission machine? A: can be one of the (double shell can be achieved in one integrated)! But most of the tattoo artist will choose to use different function of the machine! Is the so-called line machine and fog machine, fog machine can be used to secant, after add a shrapnel limit device.

 

Newsletter: for the latest offers, discount and site activity! Your email address: